阳离子型聚合物对低温低浊水的絮凝效果与形态学特性

采用微絮凝-深床直接过滤工艺,以西安市曲江水厂低温低浊水质为原水(水温低于10 ℃,初始浊度低于10NTU),投加阳离子型聚合物(简称CP)作主混凝剂或助凝剂,借助分形数学理论与图像分析技术,对滤料粒径、原水浊度、原水温度、药剂种类、聚合物分子量及投加量、混合强度等因素对处理效果的影响进行了研究,分析探讨了不同药剂处理低温低浊水的作用机理、絮凝形态学特征以及絮体结构的分形特性.结果表明,①当温度低于4 ℃、初始浊度小于4NTU时,不宜单独采用Al2(SO4)3或PAC作为絮凝剂;当温度为4～10 ℃、初始浊度小于10NTU时,如果只投加Al2(SO4)3或PAC作为絮凝剂,宜用细砂滤料过滤;低温低浊条件下,无机混凝剂形成的絮体粒径小、结构松散脆弱、有效质量密度低、沉速慢,但表征絮体分形特性的分维值较高.②CP作絮凝剂能显著改善低温低浊水的絮凝效果与过滤性能,但混合强度需增大,宜用粗砂滤料过滤;③单独用CP作絮凝剂时,宜投加分子量较低的弱阳性聚合物或投加低剂量较高分子量的强阳性聚合物;CP用作助凝剂时,能显著减少主混凝剂用量,但宜投加强阳性聚合物或增加弱阳性聚合物的剂量.④CP兼备电性中和与吸附架桥絮凝作用,能形成粒径较大、吸附性能与过滤性能良好的网状絮体构型,其有效质量密度高,产生的污泥量少,污泥沉降速度快,脱水效果好,但分维值低.⑤各种水处理药剂的处理效果为:Al2(SO4)3(或PAC) CP＞CP＞PAC＞Al2(SO4)3,这种差别由絮体的形态学特性与构型特征各异引起.     

无机高分子絮凝剂的开发与应用进展

主要介绍了各种离子型和复合型无机高分子絮凝剂的种类、原料来源、合成工艺应用情况及其絮凝机理，对无机高分子絮凝剂的发展提出了几点建议。     

聚丙烯酰胺-膨润土复合物的制备及其性能研究

采用盐酸对膨润土(BNT)进行酸活化改性,改性BNT再与氯化乙醇胺(EACl)进行阳离子交换反应,引入功能基团,得到胺化产物(ABNT-EACl).利用ABNT-EACl作为还原剂与Ce4 组成氧化还原引发体系,引发了丙烯酰胺(AM)单体的插层聚合得到了改性膨润土/聚丙烯酰胺无机/有机杂化物(ABNT/PAM).采用1H-NMR和FTIR对杂化物进行了结构表征,结果表明,杂化物中存在离子键合作用.通过实验对比研究了不同条件下的杂化物ABNT/PAM与普通絮凝剂处理工业印染废水的脱色效果,发现ABNT/PAM杂化物的效果优于普通絮凝剂.     

EFFECTIVENESS OF POLYACRYLAMIDE (PAM) IN IMPROVING RUNOFF WATER QUALITY FROM CONSTRUCTION SITES1

ABSTRACT: Erosion from construction sites significantly affects water quality in receiving streams. A rainfall simulator was used to evaluate the effectiveness of different methods for controlling erosion from construction sites. Erosion control methods investigated included dry and liquid applications of polyacrylamide (PAM), hydroseed, and straw mulch. Fertilizer was also applied to each plot to examine the effectiveness of the methods in reducing nutrient losses in runoff. Runoff samples were analyzed for total suspended solids (TSS), nitrate, total Kjeldahl nitrogen (TKN), ammonium, total phosphorus (TP), and orthophosphate. Among all treatments investigated, straw mulch was the most effective treatment for controlling TSS and nutrient losses during short term and long term simulations. The low liquid PAM (half the recommended PAM) treatment resulted in the highest reduction in runoff, TSS bound nitrogen, and total nitrogen (TN) concentrations and loadings. The study results indicate that a high application rate (twice the recommended rate) of PAM could actually increase runoff and TSS losses. At a low application rate, both liquid and dry PAM were effective in reducing TSS and nutrient losses in runoff. However, application of the liquid form of PAM to construction sites is more practical and perhaps more economical than applying the PAM in the dry form.     

羟基乙叉二膦酸镀铜废液的处理及Cu~(2+)的高附加值资源化回收

采用Na BH4还原法将羟基乙叉二膦酸(HEDP)镀铜废液中的Cu~(2+)制备成纳米铜粉,并采用聚丙烯酰胺(PAM)对还原反应后的废液进行絮凝处理。研究了n(Cu~(2+))∶n(Na BH4)、还原反应温度、还原反应时间及PAM添加量对废液中剩余Cu~(2+)质量浓度的影响,并对回收的纳米铜粉进行了XRD和TEM表征。实验结果表明:当n(Cu~(2+))∶n(Na BH4)=4∶6、还原反应温度为50℃、还原反应时间为2 h时,废液中剩余Cu~(2+)质量浓度降低至1.1 mg/L,Cu~(2+)还原率达99.99%;可获得粒径为20~45 nm的近球型、高纯度、由多晶组成的纳米铜粉;当PAM添加量为10 mg/L时,废液中剩余Cu~(2+)质量浓度降至0.35 mg/L以下,达到GB 21900—2008《电镀污染物排放标准》(小于0.5 mg/L)的要求。     

Fenton试剂降解PAM催化剂的研究

采用Fenton试剂氧化降解含油废水中的聚丙烯酰胺,研究了H2O2用量、催化剂种类及用量对降解聚丙烯酰胺效果的影响。结果表明,H2O2用量为聚丙烯酰胺的20%为宜;CuCl2具有和FeSO4、Fe(NO3)3、FeCl3相近的催化效果,并且可以作为一种在较高pH值条件下应用的催化剂;在优选条件下该氧化体系可以使聚丙烯酰胺黏度大大降低。     

电催化氧化法处理阳离子染料废水的试验研究

以结晶紫作为阳离子染料,采用电催化氧化法对阳离子染料溶液进行了电解脱色处理试验,研究了电流密度、电解质种类、电解质浓度、pH值等对该溶液脱色率的影响,测定了电解时溶液中生成的余氯浓度和溶液的紫外-可见吸收光谱曲线,并对不同电解时间的溶液的吸光度进行了归一化计算。结果表明:随着电解时间的延长,水溶液中活性氯浓度不断上升,经一定时间后达到最大值;在电催化和活性氯的协同作用下,阳离子染料结晶紫分子中的大π共轭体系被破坏、苯环结构基本瓦解,溶液快速脱色;在电流密度为5.1mA/cm2、NaCl浓度为4g/L、pH值为9.41的条件下,初始浓度为100mg/L的结晶紫溶液经过20min的电解,其脱色率可高达98.31%。     

聚合物驱采出水中聚丙烯酰胺的微生物联合降解作用研究

通过对2株细菌的培养降解实验研究聚丙烯酰胺(hydrolyzed polyacrylamide,HPAM)降解菌对水环境下聚丙烯酰胺的降解作用,讨论协同降解机理。2株降解聚丙烯酰胺的菌株假单胞菌CJ419、枯草芽孢杆菌FA16在初始30℃废水样品上培养,定期测量细菌生物量和HPAM降解率。培养30 d后CJ419和FA16对聚合物的降解率最大值分别达到30.4%和25%,而以1∶1比例的混合菌降解率最大值达到80.3%。对2株菌胞外各组分研究表明:混合菌降解HPAM的机理主要由胞外降解酶系水解聚合物侧链基团导致HPAM降解为小分子物质,同时生长过程中降解菌还会释放非蛋白还原性物质引发氧化反应共同参与HPAM降解。     

回收与降解聚驱采出水的工艺探讨

含聚污水的处理是困扰石油行业的难题之一。基于聚驱采出水的特点,围绕聚合物的回收利用和降解理论及技术,探讨国内外含聚污水处理技术的研究与应用现状,对比分析现有处理技术存在的问题及适应性,提出采用化学混凝、气浮和水质改性等技术来回收利用PAM(聚丙烯酰胺)的新思路,打破了降解PAM的传统思维,同时分析含聚污水处理与利用技术的可行性与应用前景,有望实现含聚污水的循环利用。     

Novel Polymeric Materials from Biological Oils

A variety of novel polymeric materials ranging from elastomers to tough, rigid plastics have been prepared by the cationic copolymerization of regular soybean oil, low-saturation soybean oil, or conjugated low-saturation soybean oil with various alkene commonomers. Using appropriate compositions and reaction conditions, 70–100% of the soybean oil is covalently incorporated into the cross-linked polymer networks, contributing significantly to cross-linking during copolymerization. The resulting thermosets exhibit thermophysical and mechanical properties that are competitive with those of their petroleum-based counterparts. In addition, good damping and shape memory properties have been obtained by controlling the degree of cross-linking and the rigidity of the polymer backbone. New materials with similar characteristics have also been produced from other biological oils, including tung, and fish oils using the same technique. The new, more valuable properties of these bioplastics suggest numerous promising applications of these novel polymeric materials.